You are here: Home > FRENCH DOOR INSTALLS

French Door - MaxSeal® Pet Doors Custom Made

The MaxSeal® French doors can be removed at a later time to re-install the pane of glass if you wish (excluding those that cut into the door itself). Flaps are replaceable and the door comes with a 6-year warranty.

These doors are of impeccable quality, rated to be among the best pet doors made. They provide a perfect seal and the best insulation

MaxSeal® French Doors for pets are made to order to fit the opening created by your existing panes of glass. You can replace one or more panes of glass to make room for a pet door. Some customers even will enlarge the opening by cutting into the side or footer of the door.
For more info see Installation Variations

These doors are ordered based on the opening that they will be installed into. If you are replacing one pane of glass, simply measure the exposed glass as you see it; (This will be the opening that the pet door is installed to). If you want a larger pet door than the size panes in your door, simply measure the opening you will have (more than one pane or larger due to cutting into the side or bottom of door).

Special Note: Your French pet door will have a flap size that is 2" smaller in width & height. (Due to the frame of the door itself). If you measure your pane of glass as 10"w x 10"h, then your pet door will have a flap that measures 8"w x 8"h.

Warning: If you have a single panel of glass with faux partitions in your door, do not attempt to cut the glass. Most all doors (Unless very old) are made with safety glass. If you attempt to cut it, the glass will shatter
(See picture left).

Customize Your Door by Selecting Panel & Frame Color Below

Data / Components	Installation Variations	More Info	Install Guide
Technical Specifications (Adobe Reader Required)	Ways to Install	FAQs	Pictorial Install Sequence

MaxSeal® Custom Made Pet Doors for French Doors Made in USA
Fabrication usually takes 3-5 days then ships UPS ground All French Door Units all come standard with an insulated locking panel. (Choice of white or black)
Square Inch Range (width & height of opening)	Single Flap model	Dual Flap model
0-69"	$115	$140
69-93"	$140	$170
93-141"	$175	$210
141-175"	$210	$250
175-215"	$235	$280
215-257"	$275	$325
257-309"	$310	$365
309-350"	$340	$400
350-372"	$360	$430
372-522"	$390	$465
Moore Pet Doors keeps your information on file for future replacement flaps. French Doors require 4-5 days for fabrication then ships via UPS. Note: French doors with Rough Cut Dimensions LARGER than 17.75"w x 33.75" h, require a 10 day fabrication period. The Minimum Rough Cut Dimension that theses doors can be made to is 5.5" in width or height.
A specification / data sheet will be included with your order. This will show all your measurements for the custom door so that you will be able to order replacement flaps in the future. Moore Pet will also keep this information on file. Warranty & Return Policy Doors are custom made and non-refundable

Measuring for & Installing your French Door Pet Door is very simple. (You must have individual -removable panes of glass. You cannot cut an opening into a single-solid pane of glass, your entire door glass will shatter as doors are made with Tempered-Safety glass.)

ORDERING:

Step A: Measure the exposed glass pane as you see it; without removing the molding. The door made for you will have a flap that is 2" smaller in width & height. (Make sure this resulting flap size will be large enough for your pet.)

INSTALLING:

Step B: Remove the molding around the selected pane of glass where the pet door will be installed. (If you are using more than one pane, remove molding around area.).

Step C: Remove the pane of glass and put the molding back around the opening (without glass pane).

Step D: Your pet door comes apart into 2-frames. These frames sandwich the opening and adjust to the molding thickness. Drill pilot holes for screws (the 2-frames each have a lips that glide over each other to adjust to the molding thickness. Where these two lips overlap is where the pilot holes are drilled). Put screws into pilot holes and tighten.

Note: you may at a later time remove the pet door and re-install the pane of glass.